BPDMY - PDL 333 B COMPONENT
- MSDS: BPDMY
- Manufacturer: POLYMER DEVELOPMENT LABS INC
- Product Name: PDL 333 B COMPONENT
- National Stock Number: 8030-00N030056
Product Identification
Product ID:PDL 333 B COMPONENT
MSDS Date:11/08/1990
FSC:8030
NIIN:00N030056
Kit Part:Y
MSDS Number: BPDMY
Responsible Party
ORANGE, CA 92665
US
Emergency Phone: 714-921-2300;800-424-9300(CHEMTREC)
Info Phone: 714-921-2300
Preparer: EZZAT SEIF
Cage: 1N060
Contractor
Telephone: 714-921-2300
Cage: 1N060
Ingredients
HYDROXYL TERMINATED POLY(OXYALKYLENE) POLYETHER
Fraction By Weight: 96%
TERIARY AMINE BEARING COMPOUNDS
Fraction By Weight: <2%
EXPOSED SKIN AS POSS W/APPROP CLTHG. IF SKIN
RTECS: 9999999ZZ
Hazards
LD50 LC50 Mixture:LD50:(ORAL,RAT)>5000 MG/KG
Routes of Entry: Inhalation:YES Skin:NO Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:INHAL: MAY CAUSE IRRIT TO THROAT &
RESP PASSAGES BUT @ ROOM TEMP, VAP INHAL IS NOT CONSIDERED HAZ.
SKIN: PROD CNTNS AMINE CATALYST & WILL CAUSE IRRIT TO SKIN AFTER
PRLNG CONT. SOME INDIVIDUALS MAY BE MORE SENSITIVE TO EXPOS.
INGEST: NOT CONSIDERED A COMMON OCCUPATION RTE OF EXPOS, & NO
OBSERVABLE EFTS (EFTS OF OVEREXP)
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:HLTH HAZ: HAVE BEEN DEMONSTRATED.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.
First Aid
First Aid:EYE: FLUSH W/CLEAN, LUKE-WARM H*2O @ LOW PRESS FOR @ LST 15
MIN, OCCAS LIFT LIDS. CONSULT PHYS IMMED. SKIN: REMOVE CONTAMD
CLTHG. WASH EXPOS AREA W/WARM SOAPY H*2O THORO. INHAL:NOT
CONSIDERED HAZ IN A N INDUST SITUATION. REMOVE TO FRESH AIR.
SUPPORT BRTHG. (GIVE O*2/ARTF RESP) . INGEST:INDUCE VOMIT. NEVER
GIVE ANYTHING TO DRINK TO AN UNCON PERSON/INDUCE VOMIT IN AN UNCON
PERSON. (SUPP DATA)
Fire Fighting
Flash Point Method:PMCC
Flash Point:248F,120C
Extinguishing Media:DRY CHEM EXTING SUCH AS MONOAMMONIUM PHOSPHATE,
POTASSIUM SULFATE, POTASSIUM CHLORIDE. ADDITIONALLY, CO*2, (SUPP
DATA)
Fire Fighting Procedures:NIOSH/MSHA APPRVD SCBA & FULL PROT EQUIP. DO
NOT DIRECT SOLID H*2O STREAM/FOAM INTO HOT, BURNING POOLS; MAY
CAUSE FROTH & INCR FIRE INTENSITY. (SUPP DATA)
Unusual Fire/Explosion Hazard:NONE.
Accidental Release
Spill Release Procedures:CNTN SPILLED MATL & THEN COVER W/LOOSE, ABSORB
MATL SUCH AS OILDRY, VERMICULITE, SAWDUST/FULLER'S EARTH. SHOVEL
WASTE MATERIAL INTO PROPER WASTE CONTR. WASH CONTAMD AREAS W/HOT
SOAPY WATER THORO. VENT ILATE AREA TO REMOVE VAPORS.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.
Handling
Handling and Storage Precautions:STOR TEMP: 65F(18C) TO 75F(24C). IF
CONTAM W/ISOCYANATES IS SUSPECTED, DO NOT RE-SEAL CONTR BECAUSE OF
POSS RUPTURE DUE TO PRESSURE BUILDUP.
Other Precautions:ALWAYS SLOWLY VENT CONTR WHEN OPENING TO RELIEVE ANY
PRESS BUILDUP. PROD IS HYGROSCOPIC. CONTR SHOULD BE TIGHTLY SEALED
TO PVNT MOISTURE CONTAM. DO NOT EXPOSE TO HIGH TEMP FOR ANY LENGTH
OF TIME. AVG SHELF LIFE IS 6 MTHS FROM DATE OF MFR.
Exposure Controls
Respiratory Protection:PROD HAS DEMONSTRATED NO OBSERVABLE EFTS @ ROOM
TEMP, HOWEVER, IT IS HIGHLY RECOM THAT AN NIOSH/MSHA APPRVD AIR
PURIFYING RESP W/ORG FILTER CARTRIDGES BE WORN. IN ADDN, IN ANY
SPRAY APPLICATN, A NIOSH /MSHA APPRVD SUPPLIED AIR (SUPP DATA)
Ventilation:NATL/MECH. LOC EXHAUST WILL KEEP TLV BELOW MINIMUM IN MOST
CASES. SPILLS/OTHER EMER MAY REQ MORE FORCEFUL VENT MEANS.
Protective Gloves:CHEM RESISTANT GLOVES SUCH AS(SUPP DATA)
Eye Protection:CHEM WORK GOG OR FULL LNGTH FSHLD.
Other Protective Equipment:SFTY SHOWERS & EYE WASH STATIONS SHOULD BE
PROVIDED IN ALL WORK AREAS. ALL EMPLOYEES SHOULD BE PROPERLY (SUPP
DATA)
Work Hygienic Practices:NO CONTACT LENSES SHOULD BE WORN. CONTAMINATED
CLOTHING SHOULD BE PROPERLY LAUNDERED BEFORE REUSING.
Supplemental Safety and Health
EXTING MEDIA:HIGH EXPANSION (PROTEINIC) CHEM FOAM, H*2O SPRAY FOR LG
FIRES. FIRE FIGHT PROC:BURN CAN PRDCE OXIDES OF CARBON & NITROGEN.
FIRST AID PROC:NOTE TO PHYS:BASICALLY, TRTMT IS SYMPTOMATIC. RES P
PROT:SOURCE MUST BE PROVIDED. PROT GLOVES: NATL RUB/POLYVINYL
ALCOHOL. OTHER PROT EQUIP: TRAINED. COVER AS MUCH(ING 3)
Chemical Properties
Boiling Pt:B.P. Text:DECOMPOSES
Melt/Freeze Pt:M.P/F.P Text:<32F,<0C
Vapor Pres:NIL
Vapor Density:>1.0
Spec Gravity:1.07
Solubility in Water:SLIGHTLY SOLUBLE
Appearance and Odor:VISCOUS LIQUID, CLEAR TO AMBER; SLIGHT AMMONIA
ODOR.
Stability
Stability Indicator/Materials to Avoid:YES
ISOCYANATES AND OTHER SUBSTANCES THAT REACT WITH HYDROXYL GROUPS.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:ALIPHATIC FRAGMENTS, CO, NH*3, CO*2.
Disposal
Waste Disposal Methods:WASTE MATERIAL MAY BE INCINERATED OR DISPOSED OF
UNDER LOCAL, STATE AND FEDERAL REGULATIONS CONTROLLING
ENVIRONMENTAL PROTECTION.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.